- 1 What is the function of a pull station?
- 2 What are blue pull stations for?
- 3 What is a local pull station alarm?
- 4 Are pull station addressable?
- 5 What is manual call point?
- 6 What is MCP Manual call point?
- 7 How does emergency door release work?
- 8 Do pull stations have to be red?
- 9 What is fire alarm for?
- 10 How many pull stations are required?
- 11 Which type of pull box is most likely to incorporate a tamper alarm?
- 12 What is classified as a manual alarm?
- 13 How do I reset my notifier pull station?
- 14 How do you open a fire Lite pull station?
What is the function of a pull station?
A fire alarm pull station is an active fire protection device, usually wall-mounted, that, when activated, initiates an alarm on a fire alarm system.
What are blue pull stations for?
The blue pull station, perhaps less well known, is used to alert the University of Texas Police Department (UTPD) when a situation requires police intervention. Both types of devices are usually located near exits and are activated by lifting the cover and pulling on the handle.
What is a local pull station alarm?
In short, pull stations alert the building with audibles and/or strobes lights. If a pull station is marked “Local Alarm Only,” it will make noise and lights may flash to alert people in the building that something is wrong, but you’re still going to need to dial 911.
Are pull station addressable?
Addressable manual pull stations are a single action or dual action addressable manual fire alarm pull stations for use with IntelliKnight® fire control panels. Extremely easy to operate, the addressable manual pull stations provide a fast and practical means of manually initiating a fire alarm signal.
What is manual call point?
A manual call point is a device which enables personnel to raise an alarm in the event of a fire incident by pressing a frangible element to activate the alarm system.
What is MCP Manual call point?
Manual call point (or referred to as MCP, call point or fire point) is an activation device that triggers the fire alarm by sending out signal to sirens for alert. It is placed in strategic fire points throughout the building for manual trigger of the fire alarm system.
How does emergency door release work?
When and how the emergency door release is activated When an emergency door release button is pressed. The button must be physically connected to the PACS. The button can be connected in a number of ways, which will affect how the PACS will respond to the alarm. When the fire alarm system sends an alarm signal.
Do pull stations have to be red?
A fire alarm pull station also needs to be placed between 42 and 48 inches from the floor, keeping it accessible to those who use wheelchairs. Additionally, a fire alarm pull station needs to be red and in a location that is completely unobstructed from obstacles.
What is fire alarm for?
A fire alarm system warns people when smoke, fire, carbon monoxide or other fire-related emergencies are detected. These alarms may be activated automatically from smoke detectors, and heat detectors or may also be activated via manual fire alarm activation devices such as manual call points or pull stations.
How many pull stations are required?
The National Fire Protection Association (NFPA) 101 Life Safety Code requires at least one manual fire pull station in each building. The code states that a building should not entrust life safety to only one safeguard, and directs that additional safeguards be implemented.
Which type of pull box is most likely to incorporate a tamper alarm?
Which type of bull box is most likely to incorporate a tamper alarm? Tamper-cover pull boxes.
What is classified as a manual alarm?
Manual fire alarm systems When a fire is discovered, employees must activate the alarm manually, in order to alert everybody else in the building to the danger. A typical example of a manual fire alarm system is a series of break glass units, which are installed at each point of exit in a building.
How do I reset my notifier pull station?
To reset the station, simply unlock the station with the key and pull the door open. This action resets the handle; closing the door automatically resets the switch.
How do you open a fire Lite pull station?
To activate the pull station, simply pull down the handle. The word ‘ACTIVATED’ appears after the handle is pulled down. This will remain until the pull station is reset. This pull station includes one Single Pole, Single Throw (SPST) Normally Open (N/O) switch which closes upon activation of the pull station.